|
| bore = | stroke = | block = Cast Iron | head = Aluminum | valvetrain = | compression = | fuelsystem = | management = | fueltype = | oilsystem = Wet sump | coolingsystem = Water-cooled | length = | width = | height = | weight = }} The 2.2 and 2.5 are a family of inline-4 engines developed by Chrysler Corporation originally for the Chrysler K- and L-platforms cars and subsequently used in many other Chrysler vehicles. After its launch in 1981, it became the basis for all Chrysler-developed 4-cylinder engines until the Chrysler 1.8, 2.0 & 2.4 engine family was released in 1994. ==2.2== The first version of this engine family was a normally aspirated unit. Developed under the leadership of Chief Engineer – Engine Design and Development Willem Weertman and head of performance tuning Charles "Pete" Hagenbuch, who had worked on most of Chrysler's V-8 engines and the Chrysler Slant-6 engine,〔(【引用サイトリンク】 Mopar 2.2 and 2.5 Liter Engine – Carb and TBI )〕 it was introduced in the 1981 Dodge Aries, Dodge Omni, Plymouth Horizon and Plymouth Reliant, and was produced until 2000. The 2.2 has an undersquare bore and stroke, which gives it a displacement of . It is a ''siamesed'' engine: there are no coolant passages between cylinders. The bore spacing is , limiting the potential for increased bore diameter. All 2.2 engines have cast iron blocks, use a timing belt, and are non-interference engines. The earliest version used a two-barrel carburetor, but fuel injection was introduced in 1984 on turbocharged models and 1985 on normally aspirated models (it is used on all 2.5 liter engines).〔 The initial carbureted 2.2 initially produced , but the output was increased to and . Later versions were fuel-injected and produced to and , and a High-Output version for the Dodge Charger produced and . Four series of turbocharged 2.2 and 2.5 liter engines were produced, normally referred to as Turbo I, Turbo II, Turbo III, and Turbo IV. The primary difference between these engines was the use of an intercooler (in all except Turbo I). The Turbo III, ironically developed after the Turbo IV, pioneered returnless fuel injection, and was coupled to high-performance, four-valve-per-cylinder heads, bringing from the 2.2 liter engine. The Turbo IV pioneered the use of variable nozzle technology to minimize lag.〔(【引用サイトリンク】title=The Mopar 2.2 Liter and 2.5 Liter Turbo Engines )〕 The 2.2 was made at Chrysler's Trenton Engine plant in Trenton, Michigan. In 1995, Chrysler sold much of the machining equipment, as well as a license to the design, to First Auto Works of China. The Trenton plant largely switched to the new Chrysler 3.3 engine production, while FAW continues to build the 2.2, which they used in their version of the Audi 100.〔 * 1983–1984 Chrysler E-Class * 1983–1986 Chrysler Executive * 1984–1986 Chrysler Laser * 1982–1990 Chrysler LeBaron (fuel-injected after 1985) * 1985–1988 Chrysler LeBaron GTS * 1981–1982 Dodge 024 * 1982–1983 Dodge 400 * 1983–1988 Dodge 600 (fuel-injected after 1984) * 1981–1989 Dodge Aries (fuel-injected after 1985) * 1984–1987 Dodge Caravan * 1983–1987 Dodge Charger * 1987–1988 Dodge Dakota * 1984–1990 Dodge Daytona * 1981–1990 Dodge Omni (fuel-injected after 1987) * 1985–1989 Dodge Lancer * 1982–1984 Dodge Rampage * 1987–1994 Dodge Shadow * 1985–1988 Plymouth Caravelle * 1981–1990 Plymouth Horizon (fuel-injected after 1987) * 1981–1989 Plymouth Reliant (fuel-injected after 1985) * 1983-------- Plymouth Scamp (Dodge Rampage twin) * 1987–1994 Plymouth Sundance * 1981–1982 Plymouth TC3 * 1983–1987 Plymouth Turismo * 1984–1987 Plymouth Voyager 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Chrysler 2.2 & 2.5 engine」の詳細全文を読む スポンサード リンク
|